Indian Motorcycle Forum banner

What did you do to your scout today?

1057354 Views 7803 Replies 902 Participants Last post by  Beej
finally got around to making a seat lanyard, ended up that when the seat is hanging it makes a good place to lay your tools while working with battery or making connections. also made these bungee spools for about 10 bucks. Auto part Engine Fuel line Vehicle Wire
Automotive design Vehicle Car Automotive lighting Automotive exterior
3421 - 3440 of 7804 Posts

· Registered
Joined
·
33 Posts
Auto part Vehicle Tire Automotive tire Car

Fitted Aeromach floorboards this morning. Thanks Dr Shifty.
Here they are compared to stock pegs. I also have the extended reach foot controls.

Vehicle Tire Automotive tire Motor vehicle Auto part

Not sure what the difficulty is in removing the wire locking ring - took me 10min to fit both. Two small common screw driver - one to hold the wire, the other to stretch it off the pin - then pliers to remove.

Motor vehicle Vehicle Auto part Tire Automotive tire

Will take it out for a spin tomorrow and see how they go.
 

· Registered
Joined
·
124 Posts
Put a brake light modulator on this weekend figuring it would be good to have with the day's getting shorter. Super easy install but tightening the zip ties was a bit of a pain since I could barely fit my hands in the space.

SupaBrake-3 INDIAN
where does the supabrake mount ? are the connections made under the seat?
 

· Registered
Joined
·
699 Posts
where does the supabrake mount ? are the connections made under the seat?
The connections are right under the rear fender by the brake light. After you connect everything you have several zip ties you can loop through different points and secure it tightly up against the inside of the fender and rear brake assembly. It's really easy and only a little annoying due to it being a tight space to get your hands in.
 

· Registered
Joined
·
124 Posts
The connections are right under the rear fender by the brake light. After you connect everything you have several zip ties you can loop through different points and secure it tightly up against the inside of the fender and rear brake assembly. It's really easy and only a little annoying due to it being a tight space to get your hands in.
Thank you !!! will be ordering soon
 

· Registered
Joined
·
124 Posts
How easy was the Indian USB kit to install
very easy , plug and play wiring , if your Scout is a 2018 , 2017 models will require you to run a new wire from the seat area to the headlight harness area,that wire is included in the kit. The only issue i had was getting my fat fingers on the speedo connector to remove the housing.
 

· Registered
Joined
·
26 Posts
I've ben bad. Bike 1 year old now -
Ive added:
Rack - lost seat & rear pegs - no wife allowed on bike
Crash Bars - Craigs List $35
Aeromach Slash Cuts - Mega $$
Aeromach heel/toe shifter - awesome
Ospray Custom Bags - Indian head
Easy Brackets (leather Works)
Ram mount
and today - Dart Marlin flyscreen - just for kicks

What should I do tomorrow -
 

Attachments

· Registered
Joined
·
245 Posts
I've ben bad. Bike 1 year old now -
Ive added:
Rack - lost seat & rear pegs - no wife allowed on bike
Crash Bars - Craigs List $35
Aeromach Slash Cuts - Mega $$
Aeromach heel/toe shifter - awesome
Ospray Custom Bags - Indian head
Easy Brackets (leather Works)
Ram mount
and today - Dart Marlin flyscreen - just for kicks

What should I do tomorrow -
Your whole setup is nice, but those bags are awesome
 

· Registered
2018 Scout 60
Joined
·
266 Posts
What did I do today..... I gazed lovingly upon the 60 and 69, snug in their winter berths, and sighed sadly, for the weather hath gone to shit and the ladies are tucked in for the winter. Sad months ahead until they rise like a phoenix and roar down the roads once again.
 
3421 - 3440 of 7804 Posts
Top